1. Hello there guest and Welcome to The #1 Classic Mustang forum!
    To gain full access you must Register. Registration is free and it takes only a few moments to complete.
    Already a member? Login here then!

JonnybravoM3's Recent Activity

  1. JonnybravoM3 replied to the thread Engine Swap.

    Still have the old 3 speed and that's leaking too. Was thinking of going 4spd AT. Sent from my HTC U11 using Tapatalk

    May 27, 2018 at 8:06 AM
  2. JonnybravoM3 liked Horseplay's post in the thread Fuel Tank Pressure and Gas Smell.

    Pressure is pressure. Hot or cold the valve is designed to open and close at set levels. Yes, the hotter it gets more pressure can be...

    May 27, 2018 at 5:26 AM
  3. JonnybravoM3 replied to the thread Fuel Tank Pressure and Gas Smell.

    You've always been most helpful thank you. Is there no risk to this built up pressure in one's tank? Even in the heat? Sent from my...

    May 27, 2018 at 4:38 AM
  4. JonnybravoM3 liked Horseplay's post in the thread Fuel Tank Pressure and Gas Smell.

    The valve is specifically designed to be used in a closed fuel system to protect against an over-pressurized condition. It is fine to...

    May 27, 2018 at 4:37 AM
  5. JonnybravoM3 posted a new thread.

    Fuel Tank Pressure and Gas Smell

    I have a question about our fuel tanks. Now I've always had a problem with my 65 mustang stinking up my garage with raw fuel smell,...

    Forum: Engine and Drivetrain/Mechanical

    May 27, 2018 at 3:38 AM
  6. JonnybravoM3 liked Horseplay's post in the thread Engine Swap.

    The only difference with a swap to a 302 would be if you went with a new block that incorporated a roller camshaft. Other than that the...

    May 26, 2018 at 10:55 PM
  7. JonnybravoM3 liked jims6t6's post in the thread Engine Swap.

    I'm running the original 289 in my 66. Has closer to 300K on it. Been rebuilt twice. I agree with Gary. If it's running strong put new...

    May 26, 2018 at 2:32 PM
  8. JonnybravoM3 liked turq66's post in the thread Engine Swap.

    I'm still running the original 289 in my car. Have changed the seals with the engine in the car. Currently dry and still running strong....

    May 26, 2018 at 1:32 PM
  9. JonnybravoM3 liked msell66's post in the thread Engine Swap.

    There’s no guarantee a crate motor won’t leak! Use the new Felpro rear seal and get the right oil pan gasket. Use sealer at the right...

    May 26, 2018 at 11:49 AM
  10. JonnybravoM3 replied to the thread Engine Swap.

    I could as an option but won't the seals and the gaskets be the same as those that are prone to leaks over time? I don't think they make...

    May 26, 2018 at 10:43 AM
  11. JonnybravoM3 posted a new thread.

    Engine Swap

    Hi all I'm still running the original 289 on my car and my Tech says the engine is really old and almost on its last legs even though...

    Forum: Engine and Drivetrain/Mechanical

    May 26, 2018 at 9:46 AM
  12. JonnybravoM3 replied to the thread Collected car today from the shop ... fun never stops.

    So apparently this is only the cap of the rollover vent valve and not the valve itself. Given our hot climate here I'm not so sure I...

    May 26, 2018 at 4:10 AM
  13. JonnybravoM3 replied to the thread Collected car today from the shop ... fun never stops.

    No worries thanks for your help. This is at the highest point we can manage, it is at the level of the fuel filler neck. Will go to the...

    May 25, 2018 at 5:23 AM
  14. JonnybravoM3 replied to the thread Collected car today from the shop ... fun never stops.

    When you have an arrow pointing in 1 direction, as per the attached image, is that the direction of the flow? Here's a clearer picture...

    May 25, 2018 at 5:05 AM
  15. JonnybravoM3 liked Horseplay's post in the thread Collected car today from the shop ... fun never stops.

    You can lose the rollover piece as far as I am concerned. If you are involved in an accident that results in the car being upside down...

    May 25, 2018 at 4:52 AM