I would love to be able to do a build like yours.
-
Hello there guest and Welcome to The #1 Classic Mustang forum!
To gain full access you must Register. Registration is free and it takes only a few moments to complete.
Already a member? Login here then!
Rapid Rabbit's 70 Stang
- Thread starter RapidRabbit
- Start date
We are getting closer. Exhaust is all mocked up. He just need to weld it yet. The floor pan and the aod tranny put up a bit a fight.
Fuel lines are run and just need to be finished up at the pump and filter.
Sent from my XT1058 using Tapatalk
Fuel lines are run and just need to be finished up at the pump and filter.
Sent from my XT1058 using Tapatalk
Grabber70Mach
Well-Known Member
It's looking good.
tarafied1
Well-Known Member
sweet!
Exhaust is all welded up and set. Tips are installed. I'm kind of thinking I should have gone with a different tip. The openings in the valance look a little too flat for round tips.
Sent from my XT1058 using Tapatalk
Sent from my XT1058 using Tapatalk
Last edited:
kb3
Well-Known Member
I like it!
I do too.
Thanks guys.
Maybe I'm just being over critical.
Sent from my XT1058 using Tapatalk
Maybe I'm just being over critical.
Sent from my XT1058 using Tapatalk
kb3
Well-Known Member
Although maybe the Chevy "bow tie" tips would look better on it
Then I'd have to grow a mullet again.
Sent from my XT1058 using Tapatalk
Sent from my XT1058 using Tapatalk
RyanG85
Well-Known Member
Again?
Don't ask.
My first car was a Camaro when I was 16. I learned my lesson and have been mustang ever since.
Sent from my XT1058 using Tapatalk
My first car was a Camaro when I was 16. I learned my lesson and have been mustang ever since.
Sent from my XT1058 using Tapatalk
No pictures, but a quick update.
Fuel lines are done, power steering lines and transmission lines done. All fluids filled up.
O2 sensors are getting welded in shortly.
Fingers crossed, we may be firing the engine next week.
Sent from my XT1058 using Tapatalk
Fuel lines are done, power steering lines and transmission lines done. All fluids filled up.
O2 sensors are getting welded in shortly.
Fingers crossed, we may be firing the engine next week.
Sent from my XT1058 using Tapatalk
Ignition switch is dead. New one should be her in a couple days. Then time to light the fire!
Sent from my XT1058 using Tapatalk
Sent from my XT1058 using Tapatalk
tarafied1
Well-Known Member
figures! but your getting close!
Switch showed up on Friday but the wiring was too short. Need to find a different one now. Ugh.
Maybe next week.
Sent from my XT1058 using Tapatalk
Maybe next week.
Sent from my XT1058 using Tapatalk
You're looking for a 70 ignition pigtail? I got those...but not the ignition switch side, only the underdash side.
The ignition switch on top of the column is the one I need.
Last edited:
Yeah, those are hard to find. NPD has one for $90, but states "Incl pigtail for splicing into original connector block and wire lead which must be reused."
If you need additional wire of the right colors and gauge to make the right length, I got those.
If you need additional wire of the right colors and gauge to make the right length, I got those.
70 is a goofy year with the key moved to the column.
Sent from my XT1058 using Tapatalk
Sent from my XT1058 using Tapatalk